ทดลองบนเบรดบอร์ด (Breadboard Lab)
Breadboard Lab
เลือกอุปกรณ์แล้ววางลงบนเบรดบอร์ดเอง • ระบบคำนวณวงจรจริงด้วย Nodal Analysis • LED ติดเมื่อต่อถูก
Pick components and place them yourself • Real nodal-analysis solver • LEDs light up when wired correctly
🔧 เบรดบอร์ดจำลอง (โต้ตอบได้)
🔧 Interactive Breadboard
9 V
วางขั้ว + ก่อน แล้วตามด้วยขั้ว −
Place + terminal first, then −
5 V
0 V
ไฟสลับรูปไซน์ — วางขั้ว + ก่อน · ดูคลื่นในแผง Transient
Sine AC — place + terminal first · watch the Transient panel
สายจัมเปอร์ต่อ 2 จุดให้เป็นโนดเดียวกัน (0 Ω) — สีไม่มีผลทางไฟฟ้า
A jumper joins two points into one node (0 Ω) — colour is cosmetic
วางสวิตช์ (เริ่มที่ปิด) — คลิกที่สวิตช์เพื่อเปิด/ปิดวงจร
Place a switch (starts closed) — click it to open/close the circuit
วางปุ่มกด (แบบ NO — ปกติเปิด) — กดค้างที่ปุ่มบนบอร์ดแล้ววงจรต่อ ปล่อยแล้วตัดทันที
Place a pushbutton (momentary NO) — press and hold it on the board to close the circuit; it opens the moment you let go
โหลดความต้านทาน (R = V²/P) — ไส้หลอดมีความหน่วงทางความร้อน จึงสว่างตามกำลังไฟฟ้าเฉลี่ย เหมาะกับทดสอบวงจรหรี่ไฟ (ไทรแอก/ไดแอก)
Resistive load (R = V²/P) — the filament's thermal lag means brightness follows the average power, which is what makes a TRIAC/DIAC dimmer readable
เก็บประจุ — บล็อก DC, ค่อยๆ ชาร์จผ่าน R (ดูกราฟ)
Stores charge — blocks DC, charges through R (watch the graph)
ต้านการเปลี่ยนกระแส — กระแสค่อยๆ เพิ่ม (ดูกราฟ)
Opposes current change — current ramps up (watch the graph)
3 ขา: ปลาย–ปลาย–ตัวปัด → วงจรแบ่งแรงดัน · ตัวปัดคุมด้วยลูกบิด VR
3 pins: end–end–wiper → voltage divider · wiper set by the VR knob
4 ขา: A–K (LED ฝั่งเข้า) → แสง → C–E (โฟโตทรานซิสเตอร์) · IC = CTR × IF · สองฝั่งแยกกันทางไฟฟ้า
4 pins: A–K (input LED) → light → C–E (phototransistor) · IC = CTR × IF · both sides electrically isolated
5 ขา: คอยล์ + / − → COM / NO / NC · จ่ายไฟคอยล์ถึง ~3V คอยล์ดูด → COM ต่อ NO (ปกติต่อ NC) · SPDT
5 pins: coil + / − → COM / NO / NC · energize the coil (~3V) and COM switches to NO (rests on NC) · SPDT
— V
👆 เลือกอุปกรณ์จากแถบด้านบน แล้วคลิกรูบนเบรดบอร์ด 2 จุดเพื่อวาง • คลิกอุปกรณ์ที่วางแล้วเพื่อแก้ไข
👆 Pick a component above, then click two holes to place it • click a placed part to edit it
🌍 สภาพแวดล้อม🌍 Environment
ปรับแล้วดูค่า R ของเซนเซอร์ (NTC/PTC/LDR/VR) เปลี่ยน
Adjust to see sensor R (NTC/PTC/LDR/VR) change
หมุนturn
📊 ผลการวัด📊 Measurements
🧠 เบรดบอร์ดต่อกันอย่างไร?🧠 How a breadboard connects
- คอลัมน์กลาง: รู 5 รูในแนวตั้งคอลัมน์เดียวกัน (a-e หรือ f-j) ต่อถึงกัน — วางขาอุปกรณ์ในคอลัมน์เดียวกันเพื่อเชื่อมต่อ
- ร่องกลาง แยกครึ่งบน (a-e) กับครึ่งล่าง (f-j) ออกจากกัน
- ราง + / − (บนสุด/ล่างสุด) วิ่งยาวตลอดแนว ใช้จ่ายไฟ (power rail)
- LED มีขั้ว: ขายาว = + (anode), ขาสั้น = − (cathode) — ต่อกลับขั้วจะไม่ติด
- ต้องมี แบตเตอรี่ และวงจร ครบลูป กระแสจึงจะไหล
- Column: the 5 vertical holes of one column (a-e or f-j) are connected — put component legs in the same column to join them
- The center channel separates the top half (a-e) from the bottom half (f-j)
- The + / − rails (top & bottom) run the full length — used to distribute power
- LEDs are polarized: long leg = + (anode), short leg = − (cathode) — reversed, it won't light
- You need a battery and a complete loop for current to flow